Analysis of resistance factors for LRFD of soil nail pullout limit state using default FHWA load and resistance models     

Hui Hu 《Marine Georesources & Geotechnology》2020,38(3):332-348

Abstract

Resistance factors for load and resistance factor design (LRFD) of pullout limit state of both permanent and temporary soil nails are calibrated against a wide design space using the current Federal Highway Administration (FHWA) nail load and resistance models. The calculated resistance factors were shown to scatter broadly among design scenarios that differ in wall face batter, soil friction angle, nail ultimate bond strength, and surcharge live load. An important lesson learned from the analysis results is that the current practice of using a single resistance factor for LRFD of nail pullout limit state could not result in uniform reliabilities across different design scenarios. Simple artificial neural network (ANN) models were developed for computation of resistance factors. Design examples demonstrated the ability of the ANN models in providing resistance factors that yield satisfactory and consistent reliabilities in different nail pullout designs.  相似文献   

Unified numerical study of shallow foundation on structured soft clay under unconsolidated and consolidated-undrained loadings     

Santosh Kumar Yadav  Guan-lin Ye  Usama Khalid 《Marine Georesources & Geotechnology》2020,38(4):400-416

Abstract

Based on a new elasto-plastic constitutive model, this paper presents a soil–water coupled numerical prediction of the bearing capacity for shallow foundation constructed on Ballina soft clay for unconsolidated undrained (UU) and consolidated undrained (CU) conditions. This elasto-plastic constitutive Shanghai model has an advantage of describing the mechanical behaviour of over-consolidated and structured soil under different loading and drainage conditions, by using one set of material parameter. In this paper, the Shanghai model used for both UU and CU conditions has the same initial parameters obtained from laboratory test results. The loading conditions and consolidation stages vary based on construction details. The predicted bearing pressure-settlement responses for UU and CU, approves the field observation. The phenomenon of gaining the bearing capacity due to consolidation is captured and explained by the use of soil–water coupled numerical analysis with a new elasto-plastic model. The stress strain behaviour, stress paths and the decay of the structure of elements at different depths presented in this study, reveal the mechanism for the difference between UU and CU conditions to understand the foundation behaviour. Effect of the initial degree of soil structure on the bearing capacity is also addressed. Overall, this approach provides the integrated solution for the shallow foundation design problems under short and long-term loadings.  相似文献   

Flexural performances of prestressed high strength concrete piles reinforced with hybrid GFRP and steel bars     

Ping Wu  Yang Guo  Dayong Zhu  Weiliang Jin  Zhenhua Zhang  Rongzhu Liang 《Marine Georesources & Geotechnology》2020,38(5):518-526

Abstract

This study developed prestressed high-strength concrete (PHC) piles reinforced with high-strength materials (glass fiber-reinforced polymer (GFRP) bars) for flexural performance enhancement. Flexural strengths and behaviors of PHC piles reinforced with hybrid GFRP and steel bars were experimentally investigated, respectively. Large-scale specimens with total lengths of 12,000?mm and diameters of 600?mm were constructed and tested under bending, accompanied by evaluation of effects of non-prestressed reinforcement type and longitudinal reinforcement ratio. J-factors were calculated to evaluate deformability of all the specimens. PHC piles reinforced with GFRP bars were demonstrated to have much higher flexural capacity than those reinforced with steel bars. Moreover, strains at the midspans of cross sections of all the specimens basically conformed to the assumption of plane section. Failure of PHC piles reinforced with GFRP bars was attributable to gradual concrete crushing, while that of PHC piles reinforced with steel bars resulted from steel yielding. Results of this study were expected to provide theoretical basis for wide engineering applications of PHC piles reinforced with hybrid GFRP bars and steel bars in marine structures.  相似文献   

联合BDS/GPS的北斗广域差分实时电离层延迟格网改正方法研究     

房成贺  陈俊平  兰孝奇  张磊 《大地测量与地球动力学》2019,39(2):169-177

研究并实现中国区域北斗广域差分实时电离层延迟格网改正算法，针对北斗单系统实时建立电离层延迟格网的不足，提出联合BDS/GPS的北斗广域差分实时电离层延迟改正方法。比较BDS、GPS以及BDS/GPS观测的实时电离层延迟格网，并利用北斗单频单点伪距定位进行精度验证。结果表明，在有效格网点覆盖充足的地区，BDS与GPS实时电离层延迟格网定位效果相当；而联合BDS/GPS观测的实时电离层延迟格网极大提高了偏远地区的单频定位精度与可定位历元数，也使原本单系统格网覆盖充足的地区定位效果得到进一步增强和稳定。  相似文献   

利用短期静态PPP结果反演海潮负荷位移     

魏国光  王琪洁  彭葳  郭良琦 《大地测量与地球动力学》2019,39(6):607-612

采用香港11个GPS测站的观测资料进行1 h、2 h、3 h和4h静态PPP解算，获得4组PPP坐标序列，利用调和分析求取11个测站处8个主要分潮的负荷位移参数（振幅和相位），将其与海潮模型计算的负荷位移参数进行对比，并比较分析PPP反演值与海潮模型值改正海潮负荷信号的效果。结果表明，垂直和水平方向上，不同PPP结果反演8个分潮的负荷位移分别具有约5 mm和7 mm的差异；PPP反演8个分潮垂向负荷位移优于全球海潮模型，但水平方向上的反演效果稍弱。  相似文献   

利用InSAR资料反演宁洱Ms6.4地震震源参数及库仑应力变化     

陈晨月  冯光财  高华  杨怀宁 《大地测量与地球动力学》2019,39(3):295-301

首先利用ALOS PALSAR数据，通过D-InSAR技术获取2007-06-03云南宁洱MS6.4地震的同震形变场，然后基于Okada弹性半空间位错模型反演该地震的断层几何以及精细滑动分布，最后计算宁洱地震后周边断层的静态库仑应力变化。结果表明，形变主要集中在西盘，最大视线向形变量为51.6 cm；反演得到的震源位置为23.05°N、101.02°E，深度3 km，断层走向145°，倾向49.5°，平均滑动角153°，发震断层为NNW向普洱断裂，断层活动以右旋走滑为主，兼具逆冲分量；断层面最大滑动量为1.2 m，反演得到的震级为MW619。基于库仑应力场发现，磨黑断裂处于库仑应力增加区域，而2014年景谷地震位于负值区域。结合实地考察资料和反演结果表明，宁洱地震为浅源地震，但断层并未出露地表。  相似文献   

基于GPS和水准数据的微粒群算法联合反演祁连山北缘断裂三维滑动速率     

刘杰 《大地测量与地球动力学》2019,39(9):906-909

将微粒群算法与位错理论模型相结合，采用中国地壳运动观测网络提供的青藏高原地区2001~2004年GPS测量数据和2000~2006年水准测量数据，通过常规定权和附有相对权比的方法对祁连山北缘断裂的三维滑动速率进行联合反演，并与蚁群算法反演结果进行对比。结果表明，微粒群算法收敛速度快、稳定性高，结合经典位错理论模型，是一种可以有效求解断层三维滑动速率反演问题的优化算法，在大地测量反演领域极具应用潜力。  相似文献   

多层砂土地基扩底桩单桩抗压模型试验及颗粒流模拟研究     

李飞  杨俊杰  宋琦  孙涛 《中国海洋大学学报(自然科学版)》2020,(2):116-125

利用室内半模试验和颗粒流数值模拟,揭示多层砂土地基扩底桩单桩抗压承载特性及变形特征。结果表明,通过对比分析极限承载力与H_h/D(持力层厚度与扩大头直径之比)的关系可以看出,单桩的抗压极限承载力随H_h/D逐渐增加,当H_h/D超过2.0时,极限承载力基本不再增加,此时的单桩抗压极限承载力稳定在300.01~303.25 N,是H_h/D=0.5时极限承载力(183.83 N)的1.65倍。扩大头下部土体发生局部压缩-剪切破坏,破坏面从扩大头底面边缘向斜下方扩展,在水平方向影响范围达到最大后逐渐向桩内侧收缩;荷载作用越大,地基破坏区域越大,相应的极限抗压承载力也越大;持力层厚度增加,扩大头分担的荷载比例增大,分担的荷载达到稳定需要的桩顶位移也越大,H_h=0.5 D试验扩大头分担的荷载比例稳定时为60%,对应的桩顶位移约为29 mm;桩顶位移达到33 mm后,H_h=1.0~3.0 D试验稳定在63%~65%之间;通过细观颗粒流理论对砂土移动特性的研究发现,持力层厚度从0.5 D增大至2.0 D,破坏面的起始扩展角度从31°增大至42°。数值模拟研究结果与模型试验数据吻合效果良好,证明该方法分析多层砂土地基扩底桩单桩抗压荷载传递机理是可行的。  相似文献   

Soil resistances for laterally loaded rigid piles in multi-layered elastic soil     

Bipin K. Gupta 《Geomechanics and Geoengineering》2020,15(1):10-28

ABSTRACT

Short stubby piles like monopiles and large diameter drilled shafts undergo rigid body translation and rotation when subjected to a lateral force and/or a moment at the head. A method of analysis for these piles embedded in multi-layered elastic soil is developed using the variational principles of mechanics. Using this analysis, the soil resistance against pile movement can be rigorously related to the soil elastic constants, and the pile head displacement and rotation can be quickly calculated. The equilibrium equations for pile and soil displacements are obtained using the principle of virtual work and solved using an iterative algorithm. Pile responses obtained from the analysis match well with those obtained from three-dimensional finite element analyses in which the same inputs of loads, geometry, and material properties are given. Based on the new analysis, fitted equations for soil resistance parameters are developed, which can be used to directly calculate the pile head displacement and rotation without the use of the iterative algorithm. Numerical examples are provided that demonstrate how the method can be used to analyse practical problems.  相似文献   

Reliability based assessment of axial pile bearing capacity: static analysis,SPT and CPT-based methods     

Sara Heidarie Golafzani  Abolfazl Eslami 《Georisk: Assessment and Management of Risk for Engineered Systems and Geohazards》2020,14(3):216-230

ABSTRACT

Since piles are one of the major geotechnical foundation systems, estimation of their axial bearing capacity is of great importance. Employing different design methods, resulting in a wide range of bearing capacity estimations, complicates the selection of an appropriate design scheme and confirms the existence of model error along with the inherent soil variability in bearing capacity prediction. This paper tends to evaluate different predictive methods in Reliability-Based Design (RBD) framework. In this regard, different static analyses, SPT and CPT-based methods are considered to evaluate which approaches collectively and which method individually, have more reliable predictions for compiled data bank. In order to assess reliability indices and resistance factors, two approaches have been considered, i.e. First Order Second Moment method (FOSM) and First Order Reliability Method (FORM). To investigate the reliability indices for different methods in both RBD approaches, various safety factors and loading ratios have been considered. Also, the Load and Resistance Factor Design (LRFD) resistance factors are calibrated for different target reliability indices and loading ratios. Results show that CPT-based methods are more reliable among other methods. Furthermore, the estimated efficiency ratio, i.e. the ratio of resistance factor to resistance bias factor, confirms this agreement.  相似文献